Skip to content
Koji & Steel

How to

How to Use a Whetstone: A Step-by-Step Guide for Kitchen Knives

Sharpening on a whetstone comes down to one skill: holding the same angle while you move the blade across a wet stone until a burr forms. Everything else is setup and cleanup. Plan on 20 minutes the first time and less than 10 once it is routine.

By Koji & Steel Published

We may earn a commission when you buy through links on this page, at no extra cost to you. Picks are chosen first; links are added after. Learn more.

Step by step

  1. Wet the stone

    Soaking stones, such as the King KW-65, go under water for 10 to 15 minutes until the bubbles stop. Splash-and-go stones, such as the Shapton Kuromaku, only need water on the surface. Keep a bowl of water beside you and re-wet the stone whenever it looks dry.

  2. Set it on a base that will not slide

    Put the stone on its holder, or on a damp folded towel, near the edge of the counter so your knuckles have room. Start with the coarser side up: 1000 grit for a knife that is dull but not damaged.

  3. Find the angle

    Lay the blade flat on the stone, then raise the spine until you could slide two stacked coins under it. That is about 15 degrees, right for most Japanese knives. Use closer to 20 degrees for softer Western knives. Whatever you pick, keep it constant.

  4. Sharpen the first side

    Hold the handle with one hand and rest two or three fingers of the other hand on the blade near the edge. Push the knife away from you along the stone with light, even pressure, then ease off on the way back. Work in three sections (tip, middle, heel) with 10 to 15 strokes each.

  5. Check for a burr

    Run your thumb gently across the side of the edge that was facing up, moving from the spine toward the edge, never along it. A burr feels like a faint rough lip. Keep sharpening until you can feel it along the whole length of the blade.

  6. Repeat on the second side

    Flip the knife and repeat with the same angle and the same number of strokes, until the burr has moved back to the first side.

  7. Move to the finer grit

    Turn the stone to its fine side (3000 to 6000 grit) or switch stones. Repeat both sides with lighter pressure and about half as many strokes. This refines the scratch pattern and makes the edge smoother.

  8. Remove the burr

    Finish with a few very light alternating strokes, one per side, as if you were wiping the edge on the stone. Then draw the edge backward, spine first, across a folded newspaper or a piece of leather a few times.

  9. Test, then clean up

    Slice a sheet of paper or a tomato. The knife should bite in under its own weight without sliding. Rinse and dry the knife, rinse the mud off the stone and let the stone air dry completely before you put it away.

Understanding grit

Whetstone grit works like sandpaper: the lower the number, the coarser the stone and the faster it removes steel.

Grit Job When you need it
200 to 600 Repair Chips, broken tips, re-profiling a very dull knife
800 to 2000 Sharpening Regular sharpening. 1000 is the standard.
3000 to 8000 Finishing Refining and polishing the edge after 1000

One 1000 grit stone is enough to keep a kitchen knife sharp. Our guide to the best whetstones compares the stones worth buying. A combination stone with 1000 on one side and 6000 on the other covers sharpening and finishing in one purchase, which is why it is the usual first stone.

Soaking stones and splash-and-go stones

Traditional water stones are porous. They must be soaked so that water, not the stone, carries away the metal you grind off. They wear a little faster and build up a muddy slurry that does a lot of the cutting, which many people find gives better feedback.

Harder ceramic stones do not absorb water. You wet the surface and start. They stay flat longer and suit people who want to sharpen in five minutes without planning ahead. Do not soak a stone meant for splash-and-go use; some can crack.

The mistakes that cause most bad edges

  • A changing angle. Rocking the knife rounds the edge. Lock your wrist and move from the shoulders and elbows.
  • Too much pressure. Let the stone cut. Heavy pressure gouges the stone and makes the angle harder to hold.
  • Stopping before the burr. No burr means the two sides have not met. More strokes on a finer stone will not fix that. Go back to 1000.
  • A dry stone. Add water whenever the surface stops looking wet.
  • A dished stone. Flatten the stone every few sessions.

Keeping the stone flat

Draw a pencil grid on the stone, then rub it on a diamond plate under running water until the pencil marks are gone everywhere. That tells you the whole surface is level again. A diamond plate such as the Atoma #400 is the tool most sharpeners settle on because it stays flat itself.

A note on single-bevel knives

This guide is for double-bevel knives, which covers gyuto, santoku, petty knives and nearly all Western knives. Traditional single-bevel knives such as yanagiba and deba are sharpened differently: flat on the wide bevel, then a few light passes on the back. Follow the maker’s guidance for those.

What we would buy for this

  • King KW-65 1000/6000 Combination Whetstone · King (Matsunaga Stone)

    The classic two-sided starter stone. A 1000 grit side for sharpening and a 6000 grit side for polishing, with a plastic base. It needs soaking before use.

    Made in Japan Curated and researched $
  • Shapton Kuromaku #1000 · Shapton

    A hard ceramic 1000 grit stone that works with a splash of water and no soaking. It comes in a vented plastic case that doubles as a stone holder.

    Made in Japan Curated and researched $$
  • King 1000/6000 Whetstone Starter Set · King (Matsunaga Stone)

    The King 1000/6000 combination stone bundled with a clip-on angle holder, for first-time sharpeners who want help holding a steady angle.

    Made in Japan Curated and researched $$
  • Atoma Diamond Plate #400 · Atoma (Tsuboman)

    A flat 8 x 2.8 inch diamond plate. Its main job in a kitchen is flattening water stones once they dish; it can also repair chips.

    Made in Japan Curated and researched $$

Common questions

How long should I soak a whetstone?

Soaking stones need about 10 to 15 minutes, until air bubbles stop rising. Splash-and-go stones, including most hard ceramic stones such as the Shapton Kuromaku, should not be soaked: just wet the surface. Check the maker's instructions for your stone.

What grit whetstone should I start with?

A 1000 grit stone is the standard starting point for a dull kitchen knife. A 3000 to 6000 grit stone refines the edge afterward. Coarse stones under 500 grit are only for chips and repairs.

What angle should I sharpen a kitchen knife at?

About 15 degrees per side for most Japanese knives and 15 to 20 degrees for Western knives. Consistency matters more than the exact number.

How often should I sharpen my knives?

For a home cook, a full sharpening every one to three months is typical, depending on how much you cook and what you cut on. If a knife slides off a tomato skin, it is time.

Do I push or pull the knife on a whetstone?

Both work. Most people apply pressure on the stroke where the edge trails (moving the spine first) or leads (edge first) and relax on the return. Pick one, keep the angle steady and stay consistent.

Why is my whetstone not flat any more?

Stones wear faster in the middle and become dished. A dished stone rounds your edge. Flatten it by rubbing it on a diamond plate or flattening stone under running water until the whole surface is even.